Commercial ice machines for sale, built for the hospitality industry — self contained, under bench, benchtop, modular and ice dispensing. Whether you run a cafe, bar, restaurant, pub, hotel, club or catering operation, ice is a production input like any other: if the machine cannot keep up with your busiest service, everything downstream slows down. This range covers 179 machines and accessories from Scotsman, Hoshizaki, Skope, Blizzard, Bromic and Polar, with delivery Australia-wide.
Who these commercial ice machines are for
A commercial ice machine is rated for continuous duty and specified by daily output in kilograms over 24 hours. That is the key difference from a domestic ice maker: a commercial unit is built to run all day, is plumbed in, and is designed to be serviced. Venues that typically need one include bars and pubs pouring spirits and mixers, cafes running iced coffee through summer, restaurants holding seafood and salad on ice, clubs and function venues with peaked demand, and medical, laboratory and food-processing sites with hygiene requirements.
A self contained machine has the ice-making head and the storage bin in one cabinet. It is the most common format in Australian hospitality because it is a single delivery, a single install and a single footprint. Output typically runs from around 20 kg to 300 kg per 24 hours. Browse the full range of self contained ice makers.
Under bench ice makers
Under bench (or undercounter) machines are self contained units sized to fit beneath a standard 900 mm bench, which makes them the default choice for back bars and service areas where floor space is the constraint. Height is the specification that matters — measure the gap before you order, and allow clearance for airflow and for the unit to be pulled out for service.
Benchtop and countertop ice makers
Benchtop machines sit on the counter and suit low-volume sites, offices, waiting areas and venues that only need ice for part of the day. They are the lowest-cost entry point into the category and the simplest to install.
Modular ice machines and storage bins
Modular machines are the ice-making head only and sit on top of a separate storage bin, so you size production and storage independently. This is how larger venues scale: one head, a bin sized to the service pattern, and the option to increase either later. See modular ice makers and the matching ice storage bins.
Ice dispensers and ice wells
Dispensers deliver ice on demand without an open bin, which suits self-serve areas and sites with tighter hygiene requirements. Bar ice wells and ice crushers complete a drinks station.
Ice types explained
The ice a machine produces is a real specification, not a detail. Full cube and half dice melt slowly and are the standard for spirits and mixed drinks. Gourmet or top-hat ice is clear and dense, and is chosen where the drink is on display. Flake ice is soft and mouldable, which is why it is used for seafood display, salad bars and food transport. Nugget, cubelet and chewblet ice is chewable and absorbs flavour, and is popular for soft drinks and healthcare. Crescent ice packs tightly and is common in high-volume beverage service. Choose the ice first, then the machine that makes it — not the other way round.
Commercial ice machines by venue type
Bars and pubs generally need cube or crescent ice with enough storage to cover a Friday night without the bin running dry. Cafes running iced coffee and smoothies lean toward nugget or flake. Restaurants holding seafood, oysters or salad on display need flake. Function venues and clubs are the classic case for a modular head on a large bin, because demand is peaked rather than steady. Medical and laboratory sites usually specify flake or nugget with a dispenser for hygiene reasons.
Choosing the right commercial ice machine
1. Size to your busiest day, not your average
Estimate ice per customer for your service style, multiply by covers on your busiest day, then add headroom. Under-sizing is the most common and most expensive mistake in this category, because the fix is a second machine. Note that published output figures are laboratory ratings — real-world production is lower, and falls further as ambient and water temperatures rise.
2. Check water, drainage and ambient temperature before you buy
Nearly all commercial ice machines need a cold water supply and a drain. Air-cooled machines also need clearance around the cabinet and reject heat into the room, which matters in an already-hot kitchen; water-cooled and remote condenser options exist where airflow or heat load is a problem. Australian summer ambient temperatures have a direct effect on output, so specify for your hottest month, not a mild one.
3. Match the ice type and storage to the service pattern
A machine that makes the right ice but stores too little will still fail you at peak. Storage capacity and production rate are separate numbers — check both. If the two do not line up for your venue, that is the point at which a modular head on a larger bin makes more sense than a self contained unit.
Installation, hygiene and water quality in Australia
Ice is a food, and an ice machine is food-contact equipment. Plan for routine cleaning and sanitising in line with the manufacturer's schedule, and treat filtration as part of the specification rather than an accessory — water quality affects both ice clarity and machine life, and scale is the most common cause of premature failure in hard-water areas. Plumbing and drainage work should be carried out by a licensed plumber, and electrical connection by a licensed electrician.
Complete your ice setup
Most sites need more than the machine itself. Pair a modular head with a correctly sized storage bin, add scoops and filtration, and consider whether an ice and water dispenser suits a self-serve area better than an open bin.
How much does a commercial ice machine cost in Australia?
Across the machines and accessories currently in this range, prices run from about $147 for ice-handling accessories to around $24,300 for large-capacity modular systems, with a median of roughly $5,260. Benchtop and small under bench machines sit at the lower end; high-output modular heads, large storage bins and dispensing systems sit at the top. Capacity, ice type, cooling method and brand are the main variables.
Do commercial ice machines need a drain?
Almost all of them do. Ice machines produce meltwater and purge water during the harvest cycle, and that has to go somewhere. Gravity-drained machines need a floor waste or a drain point below the outlet; where that is not available, some machines can be specified with a drain pump to lift water to a higher outlet. Confirm the drain requirement for the specific model before installation, because it determines where the machine can physically go.
Does a commercial ice machine keep the ice frozen?
The storage bin on a commercial ice machine is insulated, not refrigerated, on most self contained and modular units. Ice is held cold by its own mass and will slowly melt, with the meltwater draining away. That is normal and is why bins are sized to a service period rather than to long-term storage. If you need ice held for extended periods, that is a job for a freezer, not an ice machine bin.
What is the difference between self contained, under bench and modular machines?
Self contained describes the technology — the ice head and the storage bin in one cabinet. Under bench and benchtop describe the form factor, meaning where the machine physically fits. Most under bench machines are also self contained. Modular is the alternative technology: the head is bought separately from the bin, so production and storage are sized independently.
Which ice type should I choose?
Match it to what you serve. Cube and half dice for spirits and mixers, gourmet for drinks on display, flake for seafood and salad, nugget or cubelet for soft drinks and healthcare, crescent for high-volume beverage service. The ice type is fixed by the machine, so decide it before shortlisting models.
What size ice machine do I need?
Work from covers on your busiest day rather than an average week, allow for ambient temperature in your hottest month, and check that the storage bin covers your peak service period as well as the daily total. If production and storage requirements pull in different directions, a modular head on a larger bin is usually the answer.
Do you deliver commercial ice machines Australia-wide?
Yes. Delivery is available Australia-wide. Larger modular systems, dispensers and bins ship as freight items, so confirm site access and any lift or stair requirements when ordering.
Buying guidance
If you are unsure between formats, start from the constraint that will not move: the space the machine has to fit into, the water and drain points available, and the ice your drinks or food service actually requires. Those three narrow the field quickly. From there, size to the busiest day and allow headroom for a hot Australian summer. For a fuller walk-through of sizing and specifying, read our commercial ice machine buying guide for Australian venues, or see the breakdown of cube, nugget and flake ice if the ice type is the open question.
PURE & COOL ICE MACHINE
Hoshizaki’s Flake ice makers produce flakes consisting of 70%ice and 30% water, used primarily for cooling purposes. It is even used in large facilities such as healthcare, catering, supermarket chains or even cocktail bars. Hoshizaki’s Ice Makers are the Best Cocktail & Bar Ice Machines For Sale in Australia.
“Freeze Burn” is no longer an issue when displaying fresh fish or produce.
Carbon auger bearings have a longer life expectancy than roller bearing, reducing maintenance costs.
Automatic flush function, helps keep the ice making system clean.
Controller board with Operational Status display assists in troubleshooting.
Due to the auger system, water consumption is equal to ice production.
Can be converted to nugget ice by changing the extruding head and cutter (parts at an additional cost).
2 year parts & labour on entire unit, 5 year (parts only) on compressor & air cooled condenser coil.
Disclaimer: Image shown displays the Hoshizaki FM-480AKE with the Hoshizaki Ice Bin (Bin SOLD SEPARATELY)
Production Capacity per 24hours
Approx. 500kg @10°C Air temp; 10°C WaterApprox. 425kg @ 21°C Air temp; 15°C waterApprox. 325kg @ 32°C Air temp; 21°C water
Max Storage Capacity
Select bin and kit
Dimensions
560mm (W) x 700mm (D) x 780mm (H)
Cooling
Air
Weight Net/Gross (kg)
95 / 102
AC Supply Voltage
1 PHASE 230V 50Hz/ 10 AMP Plug
Amperage
Running: 8.4A Starting: 43A
Refrigerant Charge
R404A
Operating Conditions
Ambient Temp.: 5-40°CWater Supply Temp.: 5-35°CWater Supply Pressure: 0.07-0.8MPa (0.7-8bar)Voltage Range: Rated Voltage ±10%
Product Dimensions: 560(W) x 700(D) x 780(H)mm
All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance.
If your ice machine is not maintained, your warranty may be void.
6 Monthly Maintenance Program
Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler.
Sanitise water reservoir, distribution tubes, and bin interior.
Clean and flush condenser coils (air-cooled units).
Inspect condenser fan motor and blades.
Check inlet water valve, float, and filters for correct operation.
Verify ice thickness probe or sensor calibration.
Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary.
Test compressor amperage and general performance.
Inspect water pump operation and clean pump housing.
Check harvest cycle operation (heater or hot gas valve).
Inspect electrical connections, relays, and contactors.
Replace inline water filter cartridge.
PURE & COOL COMMERCIAL ICE MAKER
The FM-750AKE Series Commercial Ice machines produce up to 530kg of flaked ice a day which is often used for produce display of fish, fresh food and bottled beverages. In the medical field, flake ice is also used for organ transportation. Utilizing the most efficient ice making process due to the unique auger system, water consumption is equal to ice production.
“Freeze Burn” is no longer an issue when displaying fresh fish or produce.
Carbon auger bearings have a longer life expectancy than roller bearing, reducing maintenance costs.
Automatic flush function helps keep the ice making system clean.
Controller board with Operational Status display assists in troubleshooting.
Due to the auger system, water consumption is equal to ice production.
Can be converted to Nugget ice by changing the extruding head and cutter (parts at an additional cost).
2 year parts & labour on entire unit, 5 year (parts only) on compressor & air-cooled condenser coil.
Disclaimer: Image shown displays the Hoshizaki FM-750AKE with the Hoshizaki Ice Bin (Bin SOLD SEPARATELY)
Production Capacity per 24hours
Approx. 750kg @10°C Air temp; 10°C WaterApprox. 650kg @ 21°C Air temp; 15°C WaterApprox. 530kg @ 32°C Air temp; 21°C Water
Max Storage Capacity
Select bin and top kit
Dimensions
762mm (W) x 700mm (D) x 780mm (H)
Cooling
Air
Weight Net/Gross (kg)
133 / 143
AC Supply Voltage
1 PHASE 220-240V 50Hz / 15 AMP Plug
Amperage
Running: 9.2A Starting: 43A
Refrigerant Charge
R404A
Operating Conditions
Ambient Temp.: 5-40°CWater Supply Temp.: 5-35°CWater Supply Pressure: 0.05-0.8MPa (0.5-8bar)Voltage Range: Rated Voltage ±10%
Product Dimensions: 762(W) x 700(D) x 780(H)mm
All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance.
If your ice machine is not maintained, your warranty may be void.
6 Monthly Maintenance Program
Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler.
Sanitise water reservoir, distribution tubes, and bin interior.
Clean and flush condenser coils (air-cooled units).
Inspect condenser fan motor and blades.
Check inlet water valve, float, and filters for correct operation.
Verify ice thickness probe or sensor calibration.
Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary.
Test compressor amperage and general performance.
Inspect water pump operation and clean pump housing.
Check harvest cycle operation (heater or hot gas valve).
Inspect electrical connections, relays, and contactors.
Replace inline water filter cartridge.
PURE & COOL FLAKE ICE MAKER MACHINE
This modular ice maker produces flake ice, which is often used for produce display of fish, fresh food and bottled beverages. In the medical field, flake ice is also used for organ transportation. Utilizing the most efficient ice making process due to the unique auger system, water consumption is equal to ice production.
“Freeze Burn” is no longer an issue when displaying fresh fish or produce.
Carbon auger bearings have a longer life expectancy than roller bearing, reducing maintenance costs.
Automatic flush function helps keep the ice making system clean.
Controller board with Operational Status display assists in troubleshooting.
Due to the auger system, water consumption is equal to ice production.
Can be converted to Nugget ice by changing the extruding head and cutter (parts at an additional cost).
2 year parts & labour on entire unit, 5 year (parts only) on compressor & air cooled condenser coil.
Disclaimer: Image shown displays the Hoshizaki FM-1000AKE-N with the Hoshizaki Ice Bin (Bin SOLD SEPARATELY)
Production Capacity per 24hours
Approx. 1030kg @10°C Air temp; 10°C WaterApprox. 890kg @ 21°C Air temp; 15°C WaterApprox. 740kg @ 32°C Air temp; 21°C Water
Max Storage Capacity
Not Applicable
Dimensions
762mm (W) x 700mm (D) x 780mm (H)
Cooling
Air
Weight Net/Gross (kg)
146 / 156
AC Supply Voltage
1 PHASE 220-240V 50Hz / 15 AMP Plug
Amperage
Running: 12.5A Starting: 76A
Refrigerant Charge
R404A
Operating Conditions
Ambient Temp.: 5-40°CWater Supply Temp.: 5-35°CWater Supply Pressure: 0.05-0.8MPa (0.5-8bar)Voltage Range: Rated Voltage ±10%
Product Dimensions: 762(W) x 700(D) x 780(H)mm
All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance.
If your ice machine is not maintained, your warranty may be void.
6 Monthly Maintenance Program
Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler.
Sanitise water reservoir, distribution tubes, and bin interior.
Clean and flush condenser coils (air-cooled units).
Inspect condenser fan motor and blades.
Check inlet water valve, float, and filters for correct operation.
Verify ice thickness probe or sensor calibration.
Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary.
Test compressor amperage and general performance.
Inspect water pump operation and clean pump housing.
Check harvest cycle operation (heater or hot gas valve).
Inspect electrical connections, relays, and contactors.
Replace inline water filter cartridge.
PURE & COOL COMMERCIAL ICE MAKER MACHINE
This commercial modular ice maker produces flake ice, which is often used for produce display of fish, fresh food and bottled beverages. In the medical field, flake ice is also used for organ transportation. Utilizing the most efficient ice making process due to the unique auger system, water consumption is equal to ice production.
“Freeze Burn” is no longer an issue when displaying fresh fish or produce.
Carbon auger bearings have a longer life expectancy than roller bearing, reducing maintenance costs.
One piece bin moulding – rounded corners for hygiene and ease of cleaning.
Automatic flush function, helps keep the ice making system clean.
Integrated door handle for ease use and hygiene.
Controller board with Operational Status display assists in troubleshooting.
Due to the auger system, water consumption is equal to ice production.
Can be converted to nugget ice by changing the extruding head and cutter (parts at an additional cost).
2 year parts & labour on entire unit, 5 year (parts only) on compressor & air cooled condenser coil.
Production Capacity per 24hours Approx. 150kg @10°C Air temp; 10°C Water Approx. 130kg @ 21°C Air temp; 15°C Water Approx. 110kg @ 32°C Air temp; 21°C Water Max Storage Capacity Approx. 26kg -Leveled Dimensions 640mm (W) x 600mm (D) x 800mm (H) Cooling Air Weight Net/Gross (kg) 71 / 82 AC Supply Voltage 1 PHASE 220-240V 50Hz/ 10 AMP Plug Amperage Running: 5.1A Starting: 20A Refrigerant Charge R134a / 200g Operating Conditions Ambient Temp.: 5-40°C Water Supply Temp.: 5-35°C Water Supply Pressure: 0.05-0.8MPa Voltage Range: Rated Voltage ±10% Product Dimensions: 640(W) x 600(D) x 800(H)mm All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance. If your ice machine is not maintained, your warranty may be void. 6 Monthly Maintenance Program Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler. Sanitise water reservoir, distribution tubes, and bin interior. Clean and flush condenser coils (air-cooled units). Inspect condenser fan motor and blades. Check inlet water valve, float, and filters for correct operation. Verify ice thickness probe or sensor calibration. Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary. Test compressor amperage and general performance. Inspect water pump operation and clean pump housing. Check harvest cycle operation (heater or hot gas valve). Inspect electrical connections, relays, and contactors. Replace inline water filter cartridge.
USER-FRIENDLY PUSH TO DISPENSE
The Hoshizaki DB-200H H20 Minesite Crescent dispenser has a storage capacity of 85 kg and dispenses at 5kg per minute. Built with Hoshizaki’s unique ice production system inside, crescent ice is formed and kept in an enclosed bin that prevents cross-contamination.
Produce more quality ice.
Crystal clear, hard individual uniquely shaped Crescent cubes that last longer in drinks.
Use less energy.
Cycle 1/2 as many times as competition.
Cubes do not clump together in storage bins.
Unique stainless steel evaporator design which is unaffected by caustic water, harsh cleaning agents and does not crack or peel like nickel plated evaporators.
Long life stainless steel construction.
Inbuilt, removable, easily cleaned, reusable air filters.
Compatible Modular Head unit KMD-201AB, KMD-270AB orKM-660MAJ-E & Top Kit (Sold Separately)
Push Button
Single Auger Agitator
Max Storage Capacity
Approx. 91kg
Dimensions
765mm (W) x 726mm (D) x 1346mm (H)
Production
Select Modular Head unit KMD-201AA,KMD-270AA or KM-660MAJ-E & Top Kit (SoldSeparately)
Capacity Volume
5.72 ft³
Weight Net/Gross (kg)
85
AC Supply Voltage
1 PHASE 240V/ 50Hz/ 10 AMP Plug
Amperage
Rated: 1.4A
Dispensing Rate
5.89 kg
Operating Conditions
Ambient Temp.: 7-38CVoltage Range:104-132V
Product Dimensions: 765(W) x 726(D) x 1346(H)mm
All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance.
If your ice machine is not maintained, your warranty may be void.
6 Monthly Maintenance Program
Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler.
Sanitise water reservoir, distribution tubes, and bin interior.
Clean and flush condenser coils (air-cooled units).
Inspect condenser fan motor and blades.
Check inlet water valve, float, and filters for correct operation.
Verify ice thickness probe or sensor calibration.
Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary.
Test compressor amperage and general performance.
Inspect water pump operation and clean pump housing.
Check harvest cycle operation (heater or hot gas valve).
Inspect electrical connections, relays, and contactors.
Replace inline water filter cartridge.
USER-FRIENDLY PUSH TO DISPENSE
The Hoshizaki DB-200H H20 Minesite Crescent dispenser has a storage capacity of 85 kg and dispenses at 5kg per minute. Built with Hoshizaki’s unique ice production system inside, crescent ice is formed and kept in an enclosed bin that prevents cross-contamination.
Produce more quality ice.
Crystal clear, hard individual uniquely shaped Crescent cubes that last longer in drinks.
Use less energy.
Cycle 1/2 as many times as competition.
Cubes do not clump together in storage bins.
Unique stainless steel evaporator design which is unaffected by caustic water, harsh cleaning agents and does not crack or peel like nickel plated evaporators.
Long life stainless steel construction.
Inbuilt, removable, easily cleaned, reusable air filters.
*Ice Machine not included
Push Button
2 Push Buttons – 1 x Ice & 1 x Water – Single Auger Agitator
Max Storage Capacity
Approx. 91kg
Dimensions
765mm (W) x 726mm (D) x 1346mm (H)
Production
Select Modular Head unit KMD-201AA,KMD-270AA or KM-660MAJ-E & Top Kit (SoldSeparately)
Capacity Volume
5.72 ft³
Weight Net/Gross (kg)
85
AC Supply Voltage
1 PHASE 240V/ 50Hz/ 10 AMP Plug
Amperage
Rated: 1.4A
Dispensing Rate
5.89 kg
Operating Conditions
Ambient Temp.: 7-38CVoltage Range:104-132V
Product Dimensions: 765(W) x 726(D) x 1346(H)mm
All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance.
If your ice machine is not maintained, your warranty may be void.
6 Monthly Maintenance Program
Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler.
Sanitise water reservoir, distribution tubes, and bin interior.
Clean and flush condenser coils (air-cooled units).
Inspect condenser fan motor and blades.
Check inlet water valve, float, and filters for correct operation.
Verify ice thickness probe or sensor calibration.
Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary.
Test compressor amperage and general performance.
Inspect water pump operation and clean pump housing.
Check harvest cycle operation (heater or hot gas valve).
Inspect electrical connections, relays, and contactors.
Replace inline water filter cartridge.
Ice Machine Modular Half-Dice IM0485HDM Economical half-dice ice suits blending and general purpose use Hard, pure ice that’s ready for consumption and cooling alike Suitable Storage Bins: SB129, SB178 and SB453 3 Year parts warranty 1 Year labour warranty *Production /power usage based on 10degC ambient temp. and 10deg C Water temp. as tested by the Manufacturer.
Economical half-dice ice suits blending and general purpose use Hard, pure ice that’s ready for consumption and cooling alike Suitable Storage Bins: SB129, SB178 and SB453 3 Year parts warranty 1 Year labour warranty
More Information
SKU
BR-3935188
Weight (kg)
104
Colour
S/Steel
Warranty (months)
12
Ice Type
½ Dice
Ice Cube Size (mm)
29(H) x 23 (W) x 10(D)
Max. Ambient Temp. (°C / RH)
40
Ice Production (kg/24hrs)
485
Refrigeration Power (W)
2500
Refrigerant
R404a
Water Consumption (L/h)
1.4
Storage Bin Compatibility
SB406, SB178, SB243
Height (mm)
800
Depth (mm)
620
Width (mm)
760
All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance. If your ice machine is not maintained, your warranty may be void. 6 Monthly Maintenance Program Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler. Sanitise water reservoir, distribution tubes, and bin interior. Clean and flush condenser coils (air-cooled units). Inspect condenser fan motor and blades. Check inlet water valve, float, and filters for correct operation. Verify ice thickness probe or sensor calibration. Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary. Test compressor amperage and general performance. Inspect water pump operation and clean pump housing. Check harvest cycle operation (heater or hot gas valve). Inspect electrical connections, relays, and contactors. Replace inline water filter cartridge.
Bromic's Modular 160kg Half-Dice Ice Machine is suited to high-volume applications where crystal-clear, general-purpose ice is required in bulk. Rapidly producing large slabs of slow-melting half-dice ice, this heavy-duty unit can comfortably keep up in peak-periods or produce a surplus to be sold on the side. Economical half-dice ice suits blending and general purpose use Hard, pure ice that’s ready for consumption and cooling alike Suitable Storage Bins: SB129, SB178 and SB243 3 Year parts warranty 1 Year labour warranty *Production /power usage based on 10°C ambient temp. and 10°C Water temp. as tested by the Manufacturer.
Economical half-dice ice suits blending and general purpose use Hard, pure ice that’s ready for consumption and cooling alike Suitable Storage Bins: SB129, SB178 and SB243 3 Year parts warranty 1 Year labour warranty
More Information
SKU
BR-3935183
Weight (kg)
55
Colour
S/Steel
Warranty (months)
12
Ice Machine Unit
Head Only
Ice Type
Dice
Max. Ambient Temp. (°C / RH)
40°C
Ice Cube Size (mm)
29(H) x 23 (W) x 10(D)
Ice Production (kg/24hrs)
160
Refrigerant
R404a
Refrigeration Power (W)
800
Height (mm)
609
Depth (mm)
610
Width (mm)
558
Storage Bin Compatibility
SB129, SB178, SB243
All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance. If your ice machine is not maintained, your warranty may be void. 6 Monthly Maintenance Program Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler. Sanitise water reservoir, distribution tubes, and bin interior. Clean and flush condenser coils (air-cooled units). Inspect condenser fan motor and blades. Check inlet water valve, float, and filters for correct operation. Verify ice thickness probe or sensor calibration. Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary. Test compressor amperage and general performance. Inspect water pump operation and clean pump housing. Check harvest cycle operation (heater or hot gas valve). Inspect electrical connections, relays, and contactors. Replace inline water filter cartridge.
The Blizzard SN-2000P is a self-contained air-cooled cube ice machine that produces up to 900 kg of solid 22 mm ice cubes per 24 hours and stores approximately 350 kg in its integrated bin. Powered by a three-phase supply and built in stainless steel, it is engineered for the highest-demand kitchens, clubs and commercial ice production.Why operators choose the SN-2000P
Up to 900 kg/24h output — top-tier daily production for the busiest operations.
350 kg onboard storage — a substantial buffer for continuous service.
22 mm solid cubes — clear, slow-melting ice for premium drinks service.
Three-phase power — steady supply for a high-capacity machine.
Air-cooled design — no water-cooling plant required.
Premium components (Morrill pump, EBM-Papst fans, Saginomiya valve) — reliability under heavy load.
Specifications
Brand
Blizzard
Model / MPN
SN-2000P
Type
Self-Contained Cube Ice Maker
Ice type
Cube (22 mm)
Ice production
Up to 900 kg / 24h
Storage bin capacity
Approx. 350 kg
Cooling
Air-cooled
External material
Stainless steel
Power
380V / 50Hz; 4000W; three-phase + neutral
Product dimensions
1262(W) x 965(D) x 2057(H) mm
Packed dimensions
1320(W) x 910(D) x 2050(H) mm
Shipping weight
666 kg
Warranty
2 years parts and labour
Venue suitability: The SN-2000P suits large clubs, hotels, stadiums, event caterers and businesses supplying bagged ice, where daily demand runs into hundreds of kilograms. Its up-to-900 kg output and 350 kg bin cover the heaviest workloads, but it needs a three-phase power supply and professional installation, so it is not suited to sites limited to single-phase power.Compare it with the full Self Contained Ice Makers range, or browse more Blizzard refrigeration for your venue.Installation & delivery: The SN-2000P requires a three-phase power supply installed by a licensed electrician, plus a water connection, drain and ventilation clearance for air cooling. It is backed by a 2-year parts and labour warranty and dispatched Australia-wide.Frequently asked questionsHow much ice does the Blizzard SN-2000P make per day? It produces up to 900 kg of cube ice every 24 hours under normal operating conditions.What type of ice does it make? It makes solid 22 mm cube ice — clear and slow-melting, suited to premium drinks and bulk supply.How much ice can it store? The integrated bin holds approximately 350 kg.What power supply does it need? It runs on a three-phase supply and must be connected by a licensed electrician — it is not a plug-in single-phase unit.Is the SN-2000P air-cooled or water-cooled? It is air-cooled, so it needs adequate ventilation clearance around the machine.What warranty is included? It comes with a 2-year parts and labour warranty, subject to regular filter maintenance and descaling.
2 Years Parts and Labour Warranty All Ice machines MUST be maintained to ensure high performance.The cartridge on the water filter system needs to be replaced every 6 months and the unit must be de-scaled to clean the refrigeration evaporator plate.This maintains the quality of the ice shape and thickness. This program will extend machine life, improve ice quality, reduce bacterial growth risks, and ensure food safety compliance. If your ice machine is not maintained, your warranty may be void. 6 Monthly Maintenance Program Remove scale and mineral deposits from evaporator plate and water distribution system using approved descaler. Sanitise water reservoir, distribution tubes, and bin interior. Clean and flush condenser coils (air-cooled units). Inspect condenser fan motor and blades. Check inlet water valve, float, and filters for correct operation. Verify ice thickness probe or sensor calibration. Inspect refrigerant pressures, superheat, and subcooling – adjust if necessary. Test compressor amperage and general performance. Inspect water pump operation and clean pump housing. Check harvest cycle operation (heater or hot gas valve). Inspect electrical connections, relays, and contactors. Replace inline water filter cartridge.